XCMG XCT70/80/90,RETENTOR DE RODA,oil seal.860522913,860522915,860524127.CATRACA DE FREIO,arm,860528355,860528362.

XCMG XCT70/80/90,RETENTOR DE RODA,oil seal.860522913,860522915,860524127.CATRACA DE FREIO,arm,860528355,860528362.
Description



Product Overview


Two cab items are covered here for the XCMG XCT70, XCT80 and XCT90 truck cranes: the left-hand power window switch and the left-hand door lock. Both are supplied as genuine XCMG references, so the part that arrives matches the one printed on the unit it replaces.


What each item is


The switch is the rocker in the driver's door that raises and lowers the glass. The lock is the cab door lock — the latch that holds that door shut and works with the inner and outer handle. Buyers working from a Portuguese parts list know them as BOTÃO DO VIDRO ELÉTRICO LE and FECHADURA LE — the same two items, under the same numbers.


Why they come up


Cab doors on these cranes work hard. The glass runs up and down dozens of times a shift, dust finds its way into the switch body, and the door is pulled shut firmly all day. A chipped rocker, a switch that only works one way, a door that needs a slam or a handle that feels loose are all normal signs that the part is near the end of its life.


Who orders them


Fleet maintenance teams buy a switch or a lock for one machine. Independent repair shops buy for whichever crane is in the bay. Dealers who carry construction machinery spare parts for several crane brands restock both items, because the numbers turn up on the same service lists. Each item can be ordered on its own, by number, from a single piece.


Where they come from


We work as crane parts suppliers from Shenyang, close to the factories and the freight terminals, which is why cab items leave quickly. Fast-moving door parts sit on the same shelves as the crane hydraulic parts and undercarriage groups, so one repair does not turn into three shipments from three sources.


One caution


These cranes went through several cab builds, so mobile crane spare parts like these should be ordered from the number moulded on the old unit rather than from a description. If that number is not on the list below, treat the part as a different variant until it has been checked.


Part Numbers & Left-Side Marking


DescriptionReference
Power window switch, left860502872
Power window switch, left860502873
Earlier reference for the same switch860150175
Power window switch, left860502716
Door lock, left802141257
Door lock, left802141255
Cab positionLeft-hand door, driver's side when seated in the cab facing forward
Machine familyXCMG XCT70, XCT80 and XCT90 truck cranes
Catalogue namingBOTÃO DO VIDRO ELÉTRICO LE (window switch); FECHADURA LE (door lock)
SupplyGenuine XCMG spare parts reference, matched by number

Window Switch & Door Lock Operation


What the switch does


The rocker sits where the driver's hand falls naturally and rests in a middle position. Pressing one side feeds the window motor one way, pressing the other side reverses the feed, and the glass follows. There is nothing to program: the switch is a set of contacts with a plug on the back that mates with the door wiring, and the unit is held in the trim by its own clips.


What the lock does


The XCMG door lock turns a claw around the striker on the door frame and holds it closed until the inner handle, the outer handle or the lock lever releases it. A short rod links the latch to the handle, and the springs and pivots inside the latch body do the real work. Once the door is shut, the latch and the striker carry the load, not the handle.


Which side


LE is the left-hand door, taken from the driver's seat facing forward. The right-hand items are mirror parts, with a different latch body, a different striker slot and a different release direction, so the two sides never substitute for each other.


Where they sit in the machine


The switch belongs to the cab's crane electrical parts and the lock is body hardware. Neither touches the driveline or the lifting system, so a failure never stops the crane working — it makes the cab uncomfortable, and a door that will not latch makes the machine awkward to move around site. That is why fleets and crane parts suppliers keep both within reach rather than waiting for a failure.


Two parts, one door


The switch and the lock rarely fail on the same day, but they are ordered together often enough that we keep them side by side. A door that has been swung shut for years usually has a tired latch and a rocker with a chipped edge at the same time.


Fault Symptoms & Diagnosis


  • Start from the symptom. Most crane spare parts calls on the cab follow one of the patterns below, and matching the pattern first is what stops a working switch being replaced because of a tired motor.
  • Dead in both directions. Check the fuse, the relay and the plug on the back of the switch before condemning it. If the interior light dims or the motor hums when you press the rocker, the switch is doing its job and the fault is further down the circuit.
  • Works one way only. Usually a worn contact inside the XCMG window switch: the glass still travels smoothly in the direction that works, which tells you the motor and the regulator are sound.
  • Cuts in and out over bumps or after rain. A loose plug or corroded terminals at the switch or in the door wiring. Reseat the connector and look for green corrosion before ordering anything.
  • Rocker feels slack or will not spring back. The switch body itself is worn. It may still work now and then, but the part is on its way out.
  • Switch clicks, glass grinds or crawls. That is the regulator, the glass channel or the motor — a new switch will not make a slow glass fast.
  • Door needs a slam, rattles, or will not open from inside. Latch wear, a stretched or detached rod between handle and latch, or a striker that has moved. Read the wear marks on the striker before blaming the cab door lock.
  • Only this door fails to lock. On a machine with central locking, check the rod between the actuator and the latch, and confirm the rod still moves the release lever.
  • One-minute isolation test. If another machine nearby runs the same switch, plug its switch into this door wiring. If the glass then moves, the wiring and motor are fine and the switch is the fault.

Fitment Checks Before Ordering


Ordering construction machinery spare parts from a description is where most wrong-part orders begin. The number moulded or printed on the old unit is the reference to work from — not the model name, not a photograph of a similar door.


Side


LE is the left-hand door as you sit in the driver's seat. A right-hand lock has a mirrored latch body and release direction and will not fit the left door, so settle the side before you settle the number.


Connector and terminals


Count the terminals in the plug on the back of the old switch and note the shape of its keyway. Two switches can look identical from the front of the trim and still not plug into the same wiring loom, and this is the detail that separates one cab build from another.


Mounting and rocker


Look at how the old XCMG window switch is held in the trim — clip pattern, screw holes, the size of the aperture — and at the rocker profile. A different rocker will not sit flush in the same opening, and a different clip pattern will not hold.


The lock


On the XCMG door lock, compare the striker slot, the bolt pattern on the latch body and the direction the release lever travels. Check as well whether the linkage rod is held by a clip or a pin, because the new latch has to accept the rod you already have on the door.


Machine plate


Confirm the model on the plate — XCT70, XCT80 or XCT90 — and note the cab build where it is stamped. When the number on the part is worn away, the plate plus the physical details above are what the identification is built from.


When the number does not match


A part carrying an unlisted number is a different variant until it has been checked, even if it looks identical in the door. XCT70 cab parts are built to a number, and the number is what the drawings are checked against.


Installation & Adjustment


  1. Park the crane on level ground, lower the glass about a third of the way and disconnect the battery negative before touching any cab wiring.
  2. Remove the screws and clips along the door trim panel, ease the panel away and peel back the liner far enough to reach the back of the switch.
  3. Release the retaining clip, unplug the connector and lift the old switch out. Compare the new unit against it — terminals, clip pattern and rocker — before it goes in.
  4. Plug the new switch in and test the glass up and down with the battery reconnected and the trim still off, so a bad connection shows up before everything is reassembled.
  5. For the XCMG door lock, mark the striker position on the door frame, support the door, then unbolt the latch and unhook the linkage rod and the release lever.
  6. Fit the new latch, reconnect the rod and both handles, and close the door onto the striker gently. Move the striker up, down or in until the door shuts with a firm push and no lift.
  7. Reconnect the battery, run the glass through its full travel and check the inner handle, the outer handle and the lock lever before the machine goes back to work.

Ordering & Delivery


  • Order from the number. Quote the reference from your old unit. Quantity can start from 1 piece, so a single failed switch is not a problem.
  • Payment and lead time. T/T; Western Union or as agreed. Most parts in stock; usually 7-20 days, according to the quantity.
  • Shipping and packing. EXW, FOB, CFR, CIF; shipped via Shanghai, Dalian, etc. Structural items travel in sea-worthy wooden crates or steel frames, and small cab parts are packed inside the consignment rather than loose.
  • Warranty. 2500 working hours or one year.
  • One consignment. Switch, lock, door hardware and other crane spare parts for the same repair can leave together instead of as three separate orders.
  • Checked before dispatch. Our engineers cross-reference the XCMG crane parts on every order against the original drawings before packing, so a wrong number is caught in Shenyang rather than at your workshop door.
  • The wider shelf. Beside the cab items we hold crane hydraulic parts for these machines, so the next item on the service list usually ships from the same place.
  • Cab electrics and other machines. Cables, controllers, monitors, sensors, limiters and switches make up the crane electrical parts group, and parts for other Chinese-built equipment are held alongside it.

Technical Support & Model Matching


Not sure which part fits your machine? Send the part number, the machine model, and a photo of the nameplate or the worn item, and our engineers — each with more than ten years in the construction machinery business — will confirm the correct reference and quote it. We advise on installation, help trace faults, and answer technical questions before and after dispatch. Since 2017 we have built this support on a supplier network covering FUWA, SANY, XCMG and ZOOMLION, so XCT70 cab parts and other older, hard-to-find references can usually still be sourced.


FAQ




Q1. Which models and which side do these parts fit?


Both items are listed for the XCMG XCT70, XCT80 and XCT90 truck cranes, on the left-hand door — the driver's side when you are seated in the cab facing forward. The LE in the catalogue name is the side marking. Left and right parts are mirror versions and are not interchangeable, so a right-hand door needs a different lock and a different switch. If the door on your machine carries a number that is not on the list, it is a different variant — send it over and we will check it against the XCMG spare parts we hold for these models.




Q2. How do I tell whether the window switch or the regulator has failed?


Watch the glass rather than the switch. If it travels smoothly in one direction and not at all in the other, the motor and regulator are working and a contact inside the switch is worn. If it grinds, crawls or stops halfway in both directions while the switch still clicks, the fault is behind the trim — regulator, glass channel or motor. This is the most common mix-up on mobile crane spare parts for the cab, and it costs a workshop an extra part every time it happens. A known-good switch from another machine plugged into the same door wiring settles it in a minute.




Q3. What if the number on my old switch is worn away?


Match on the details around it instead. On the switch that means the number of terminals in the plug and the shape of its keyway, the rocker profile, the clip or screw pattern that holds the unit in the trim, and which door it came from. On the lock it means the striker slot, the bolt pattern and the direction of the release lever. The machine plate narrows the model; these details narrow the variant. Cab builds changed over the production run, so mobile crane spare parts like these are confirmed against the drawings rather than guessed from a photograph.




Q4. Can you supply the rest of the cab and other parts for the same machine?


Yes. Window regulators, door handles, hinges, seals, cables, controllers, monitors, sensors, limiters and switches all sit in the same cab and electrical group, and the crane hydraulic parts these machines run on come from the same warehouse. The range runs across crawler cranes, truck and all-terrain cranes and rotary drilling rigs. Because most of it can ship together, a door rebuild and a hydraulic service can leave Shenyang on one consignment instead of three — send the machine model and the list of numbers and we will put it together.




Q5. Can your technicians help with fitting and testing?


Yes. Cab faults are the kind of thing our technicians work through every week, and this is one of the simpler crane electrical parts to prove: describe what the glass and the lock are doing and they will tell you which terminal to check and whether the fault sits in the switch, the wiring or the motor. The same team checks each order against the original drawings before it ships, so fitment is settled before the part leaves Shenyang rather than after it arrives on site.




Q6. Do you also supply custom or made-to-order parts?


Boom and attachment parts are the ones we build to order — sections, jib inserts and attachment work for XCMG crane and rotary drilling rig models, made to suit the machine on your site. These cab controls are different: they are supplied against the original references, because a window switch or a door latch has to match the cab exactly. If you are after something that is no longer in the catalogue, send the details — legacy and discontinued items are one of the main reasons buyers come to us for construction machinery spare parts.




Q7. Are these genuine XCMG parts?


They are supplied as genuine XCMG references, matched to the number on the old unit and cross-checked against the original drawings before dispatch. Where a part has to come from a different source to keep a machine running, you are told before the order ships rather than after. That is the standard we apply across the XCMG crane parts we supply, and it is why a cab order is usually the start of a longer parts list rather than a one-off.




Review

1/3
X