XCMG XCT35/70/90/100/110/XCA,Spring,860507692(860144439),hydraulic Lock,803000738,steering pump,804008407,power switch,803600744,power relay,803750655.

XCMG XCT35/70/90/100/110/XCA,Spring,860507692(860144439),hydraulic Lock,803000738,steering pump,804008407,power switch,803600744,power relay,803750655.
Description



Product Overview


An XCMG XCT or XCA truck crane has a short list of cab parts that fail long before anything in the driveline does: the left-hand window regulator that lifts the side glass, two door grip references, the motor brake on the window drive, and the spring that keeps the door assembly under tension. All of them are listed here under their XCMG numbers, so a workshop can repair a damaged cab door in one order instead of chasing the regulator this week and the spring next week. Small XCMG crane parts like these are what most cab repairs actually consist of.


Nothing in the group is electronic — no connector to test, no software to load. The regulator is supplied as a complete mechanism with its motor fitted, and the grips, brake and spring bolt straight on. That alone separates these items from the crane electrical parts in the same cab: a fitter can strip the door card, swap the worn part and refit it inside one shift, on a machine that is losing money by the hour.


Small crane spare parts are also the ones most often ordered late, after a temporary repair has already failed twice. Buying the whole group against one machine costs less than a second shipment and leaves the workshop holding the parts the next door repair will need.


Cab Parts by Position


  • Left window regulator — the complete lifting mechanism for the left-hand side glass, with the drive motor attached and the connector ready to plug in. Replace it when the glass rises crooked, drops on one side, or when the motor turns and nothing moves.
  • Door grips, two references — these cover the handles on the cab door and they are position-specific, so the two references are not interchangeable. Read the number on the back of the failed handle before ordering; once both are off the door they look almost the same, which is why crane parts suppliers work from the number rather than the shape.
  • Motor brake — works with the window drive to hold the mechanism when the motor is not running. A brake that has worn lets the glass creep down from the position it was left in, or makes the motor labour near the top of its travel.
  • Cab spring — the return spring in the door assembly. A tired spring is why a handle feels slack or a latch no longer snaps back, and it is the item most often skipped when the door is already apart for something else.
  • Handing — the regulator here is the left-hand unit, shown by the L in its Portuguese catalogue name MÁQUINA DO VIDRO L. If the failure is on the opposite door, say so when you enquire and we will quote the matching right-hand reference from the same XCMG crane parts list rather than send a part that cannot fit.

Specifications


Part groupCab and body hardware
Window regulator802149443, left-hand (catalogue name MÁQUINA DO VIDRO L)
Door grip802141258
Door grip802141254
Motor brake800900047
Cab spring860507692 (860144439)
Machine coverageXCMG XCT35/70/90/100/110, XCA
Part typeMechanical cab fittings, no electronics; crane electrical parts are a separate group
HandingLeft-hand regulator; right-hand reference quoted to order
SupplyIndividual XCMG spare parts, or the complete group in one shipment

Model Coverage and Fitment


The regulator, grips, brake and spring are listed for the XCMG XCT35, XCT70, XCT90, XCT100, XCT110 and XCA cranes. One regulator reference serves the whole XCT35 to XCT110 group, so the cab door hardware is common across that family; if your machine is an early or late build, send the serial as well as the model and we will check it before the order is confirmed. That check is the whole job with XCMG spare parts — a number on a listing only helps if it is the number your machine was built with.


Fitment is confirmed against the original XCMG drawing rather than a photograph or a description, the same routine we apply to every construction machinery spare parts order we ship. Give us the model, the year and the number from the old item; our engineers cross-reference it and come back with the confirmed reference before anything is packed. Where a reference has been superseded we tell you what replaced it, and where what you need is an alternative rather than the original, we say so before you order.


Because these are cab parts, one carton can carry mobile crane spare parts for several machines on the same lot. Fleets running an XCT35 next to an XCT110, or an XCA alongside older XCMG units, usually put the whole cab list into one shipment rather than paying freight three times for three small items.


Identifying the Correct Reference


  1. Read the number off the old part first. Every item here carries an XCMG number moulded or stamped on the body, and that number — not the description — is what decides the mobile crane spare parts order.
  2. Note the side. The regulator listed here is the left-hand unit; if the glass that failed is on the other door, tell us and we quote the opposite reference instead.
  3. Write down the machine model and serial from the plate, including any build prefix. Two cranes with the same badge can carry different door hardware late in a production run, and that is the most common reason an XCMG spare parts order comes back as a wrong fit.
  4. Photograph the old item where it mounts, plus any lever arm or connector. A photo settles in one look what three emails of description cannot.
  5. Send the lot to us before you order. We check the number against the XCMG drawing, confirm the reference and flag any supersession, then the crane spare parts order goes ahead with the right part in the box.
  6. Keep the old part until the new one is fitted. Numbers wear smooth on high-hour machines, and on a construction machinery spare parts job, comparing old against new settles any doubt in the workshop rather than on site.

Fitting, Care and Shelf Stock


  • Clean the track before the new regulator goes in — dust and dried grease in the window channel are what kill a replacement mechanism early. Wipe the channel out and check the guide is straight while the door card is off.
  • Support the glass first — hold the glass up before the regulator is unbolted, or it drops the moment the last fastener comes out.
  • Run it by hand before reconnecting the motor — with the drive disconnected, the new mechanism should move smoothly through its full travel. If it binds, the fault is in the track or the guide, not in the part you just bought.
  • Do not force a stiff window — running a binding window up and down on the motor strips the brake and bends the guide. Stop, free the track, then test the drive.
  • Change the spring with the handle — a grip that feels loose usually has a tired return spring behind it. The two are low-cost construction machinery spare parts, worth doing together to save opening the same door twice.
  • Keep one of each on the shelf — a spring, a grip and a regulator cover most cab failures on an XCT fleet. Any crane spare parts counter will tell you the same: the low-cost item in the drawer is what saves the shift, and these store small without ageing.

Ordering and Delivery


Minimum order1 piece per item
PaymentT/T; Western Union or as agreed
Lead timeMost parts in stock; usually 7-20 days according to quantity
Shipping termsEXW, FOB, CFR, CIF
Port of loadingShanghai, Dalian or another Chinese port to suit the route
Warranty2500 working hours or one year
PackingSmall hardware bagged separately, then wrapped and boxed for export
ConsolidationCab hardware can ship with crane hydraulic parts, filters or undercarriage items from one warehouse
Related supplySensors, controllers and other crane electrical parts quoted from the same stock list

Technical Support & Model Matching


Not sure which part fits your machine? Send the part number, the machine model, and a photo of the nameplate or the worn item, and our engineers — each with more than ten years in the construction machinery business — will confirm the correct reference and quote it. We advise on installation, help trace faults, and answer technical questions before and after dispatch. Since 2017 we have built this support on a supplier network covering FUWA, SANY, XCMG and ZOOMLION, so older and hard-to-find references can usually still be sourced.


FAQ




Q1. Which XCMG models do these cab parts fit?


The regulator, door grips, motor brake and spring are listed for the XCT35, XCT70, XCT90, XCT100 and XCT110 truck cranes and the XCA models. The same cab hardware group also covers other XCMG machines we handle within our XCMG crane parts range, including QUY crawler cranes, QY truck cranes and XR drilling rigs. If your model is not on that list, send the model and serial and we will check the drawing. On a machine that has been through a cab rebuild, the plate on the door pillar is a better guide than the badge.




Q2. How do I know whether I need the left window regulator?


The reference listed here is the left-hand mechanism, which is why the Portuguese catalogue name carries the L for left. If the glass that has failed is on the right-hand door, tell us before you order and we will quote the matching right-hand reference instead of sending a part that will not fit. The other clue is on the motor itself: read the number from the old unit and compare it with the new part before the door card goes back on.




Q3. Which door grip reference do I need — 802141258 or 802141254?


The two references cover different handle positions on the cab door, so the position that has failed decides it, not the shape. Read the number moulded into the back of the old grip; if it has worn smooth, send a photo of the handle in place and we will match it. Ordering both is common on a high-hour machine, because once one handle is worn oval the other is usually close behind.




Q4. Do you supply more than cab hardware?


Yes. Cab and body parts are one small group inside a much wider range of mobile crane spare parts: hydraulic pumps, valves and cylinders; undercarriage track shoes, rollers and sprockets; controllers, monitors and sensors; plus boom and attachment parts. Buyers who start with a door grip often come back for the rest of the list once they see how the first order is handled, and keeping a fleet on one supplier list saves a lot of freight.




Q5. Do you provide technical support for overseas customers?


Yes — the team answers enquiries around the clock and helps with part selection, fitting and commissioning. Send a photo of the failed item in place and describe what the machine is doing, and we can usually say whether the regulator, the brake or the door hardware is at fault before you order. For a buyer working with crane parts suppliers for the first time, that check is often the difference between a repair and a return shipment.




Q6. Do you accept customization for boom and attachment parts?


Yes. Boom sections and attachment parts can be made to suit different XCMG crane and rotary drilling rig models. Send the machine model, the section or attachment you need and any drawings you have, and we will confirm what can be produced and how it is specified. The cab hardware on this product — window regulator, grips, brake and spring — is supplied to the original reference rather than customized.




Review

1/3
X