XCMG QUY80,QUY150,QUY650 Fuel Tank Cap, 172101949.

XCMG QUY80,QUY150,QUY650 Fuel Tank Cap, 172101949.
Description



Product Overview


The speed sensor is the right-angle pick-up that reports how fast a driven function on the crane is turning. On the QUY80, QUY150 and QUY650 it is held by a flange with a single fixing hole, threads into the housing on a metallic nose, and takes its cable out of the body at 90 degrees so the run clears the pipework around it. A black plastic housing protects the electronics, and because the cable is moulded into the body rather than plugged in at the sensor end, the unit is changed as one piece.


One reference covers all three crawler crane models, so the QUY80 speed sensor on your shelf is also the one for a QUY150 or a QUY650, which matters when you buy mobile crane spare parts for a mixed fleet. The body carries the XCMG reference and the Rexroth numbering side by side, so an order can be raised from either the crane documentation or the component documentation.


Treat it as a crane electrical part and nothing more. No hydraulic circuit is opened to change it, and the only mechanical work is unseating the old nose and seating the new one. Small construction machinery spare parts like this are easy to skip during a service, which is why the failure usually announces itself through the control system rather than through anything visible on the deck.


Specifications


PropertyDetail
Part nameSpeed sensor
CategoryCrane electrical parts
XCMG reference803180734
Rexroth speed sensor cross-referenceR902082727 / R902602512
Machine modelsQUY80, QUY150, QUY650 crawler cranes
Sensor functionRotational speed feedback
Body formRight-angle, flange-mounted
HousingBlack plastic
Sensor noseMetallic, threaded
MountingFlange with one fixing hole
ConnectionCable moulded to the body
MarkingsXCMG reference and Rexroth numbering on the body
Supplied asOne sensor with cable

Part Number Cross-Reference


Two numbering systems meet on this sensor, and buyers arrive holding either one. The XCMG reference 803180734 is the number in the crane's parts book and on the XCMG label; R902082727 and R902602512 are the Rexroth speed sensor numbers, etched on the side of the body and quoted wherever the machine was documented from the component side. Both point to the same right-angle unit, so an xcmg crane parts order raised against either number arrives as the same sensor.


Read the number off the old body rather than off an invoice or a dealer's email. Laser etching fades on a unit that has spent years in dust, so a clear close-up of the side marking and of the connector end is the fastest way to confirm a match. Where a number has been superseded, the replacement can carry a different suffix while keeping the same housing, thread and connector; send the photograph and the match is confirmed before you commit.


Do not choose on appearance. Right-angle speed sensors exist in several thread and connector configurations, and two units that look identical in a photograph can differ in nose length or pin arrangement. The number is the reliable identifier — the shape only tells you that you are looking at the right family of xcmg spare parts.


Failure Symptoms and Diagnosis


  • The speed reading drops out or jumps. The display shows nothing, or a figure that climbs and falls while the throttle is held steady, on the function the sensor serves.
  • The control system protects itself. When feedback disappears, the crane can drop into a restricted working mode rather than stop outright, so the first complaint is often about a limiter or a lockout rather than a sensor.
  • The fault comes and goes with heat. A failing winding inside the body can behave perfectly from cold and misbehave after an hour under load, which is how a sensor gets changed and then blamed again when the fault returns.
  • Look at the nose before condemning the unit. Metal filings, packed grease or a nose knocked out of alignment will disturb the reading; clean around the sensor before it is unseated so nothing drops into the housing.
  • Check the electrical side first. Pull the cable along its run for chafing, look at the connector pins for corrosion, and read any stored code before you order xcmg spare parts. A fault that behaves like a dead sensor can sit in the loom.
  • Do not assume hydraulics. A winch that will not hold speed reads like a crane hydraulic part problem, and on a machine of this age the pressure side deserves a look — but confirm the speed signal first, because changing hydraulic components to cure a missing electrical signal gets expensive quickly.
  • Watch for a repeat failure. If a replacement has already failed, the cause is usually seating, cable routing or contamination rather than the new unit, and the crane electrical parts around it deserve the same attention.

Installation and Commissioning


  1. Park the machine on firm ground, bring the boom to its rest and isolate the battery master switch before touching the sensor.
  2. Photograph the old QUY80 speed sensor in place — body, cable route and connector — so the new one goes back in the same orientation.
  3. Release the connector at the loom end rather than pulling on the cable, then take out the fixing screw at the flange.
  4. Unscrew the sensor by hand once it is free and wipe the seating face clean. Check the sealing ring; if it is hardened or flattened, fit a new one.
  5. Start the new unit by hand to avoid cross-threading, bring it down until the flange meets the face, then refit the fixing screw. If you need a torque figure for your machine, ask our technicians before tightening.
  6. Route the cable along the original path, clear of hot surfaces and frame edges, and secure it at the same clip points.
  7. Start the machine, run the function through a slow cycle and watch the reading. If it stays blank, recheck the connector and clear stored faults with the diagnostic tool before removing the new crawler crane sensor.

Ordering and Delivery


  • Minimum order. 1 piece — single construction machinery spare parts and mixed repair lots go through the same process.
  • Payment. T/T; Western Union or as agreed.
  • Lead time. Most parts in stock. Usually need 7-20 days, according to the quantity.
  • Shipping terms. EXW, FOB, CFR, CIF; shipped via Shanghai, Dalian, etc.
  • Warranty. 2500 working hours or one year.
  • Packing. The sensor travels in its own protective bag with the cable coiled and tied, inside export packing built for sea freight; larger structural items go in wooden cases or steel frames.
  • What to include. The number from the body or a photograph of it, the machine model and serial, the quantity, and your shipping term and destination port.
  • Consolidation. A repair rarely needs one item. If the same job also calls for a seal kit, a pressure sensor or another crane hydraulic part, list it on the same order and the items ship together; this is how most of our xcmg spare parts repeat orders are built.
  • Mixed fleets. The QUY150 speed sensor is the same part as the QUY80 and QUY650 units, so one line on the order can serve several machines, and other mobile crane spare parts on the same list are checked against their own references.

Quality and Fitment Checks


  1. Reference match. The number you ordered is cross-referenced against the original drawing held for that machine, and against our records of xcmg crane parts already supplied for the model, before anything leaves the shelf.
  2. Body, thread and flange. The nose thread, body angle and flange hole are compared with the reference, because these are the points where a look-alike unit usually differs.
  3. Connector and cable. Pin arrangement, cable length and the angle at which the cable leaves the body are checked against the machine's loom, so the unit plugs in without an adapter.
  4. Markings. The etching and brand markings are read and recorded, so the part in your hand can be compared with the part in your photograph.
  5. Genuine supply, stated plainly. We supply genuine XCMG parts and Rexroth-built components for XCMG machines. Where a reference has been superseded, you are told before dispatch instead of finding out at the machine.
  6. Before you fit it. Compare the number on the body with the number on your order, and keep the packaging until the crane has run through a full cycle. A mismatch is settled on the number, not on a description — send a photograph of the marking and it is dealt with.
  7. Why the check matters. As a crane parts supplier working with fleets and workshops rather than production lines, our value sits in this step: the machine is already down, and a second wrong part costs another week.

Related XCMG Parts


Part groupWhat we supply
HydraulicRexroth pumps and motors calibrated for XCMG systems, valves, cylinders and seal kits
Undercarriage
Electrical and safetyCrawler crane sensors, controllers, monitors, limiters, cables and switches
Boom and attachmentBoom sections, jib inserts, hook blocks, sheaves and wire rope
Cab and bodyWindow regulators, door grips, locks, springs, glass and cab switches
MaintenanceFilters, repair kits, engine parts, brake and clutch items
Legacy and customDiscontinued references manufactured to order, and boom and attachment parts made to suit specific models

Technical Support & Model Matching


Not sure which part fits your machine? Send the part number, the machine model, and a photo of the nameplate or the worn item, and our engineers — each with more than ten years in the construction machinery business — will confirm the correct reference and quote it. We advise on installation, help trace faults, and answer technical questions before and after dispatch. Since 2017 we have built this support on a supplier network covering FUWA, SANY, XCMG and ZOOMLION, so older and hard-to-find references can usually still be sourced.


FAQ




Q1. Which XCMG models does this speed sensor fit?


QUY80, QUY150 and QUY650 crawler cranes — the three models that share this reference on the driven function. Beyond them we handle xcmg crane parts for crawler cranes, truck and all-terrain cranes and rotary drilling rigs, so if you run a different model, send the machine plate details and the number from the old unit and the correct reference is checked for you. Mobile crane spare parts for the truck and all-terrain ranges use different sensor references, so this unit should not be assumed to cross over to them.




Q2. Is this the same part as the proximity sensors used on the QUY series?


No. The proximity sensors on these cranes are barrel-bodied inductive units in M18 and M30 bodies that detect a target passing in front of them, while this is a flanged speed pick-up with a threaded metallic nose and a cable moulded to the body. Both sit in the same electrical area, which is why they get confused. This is not a crane hydraulic part either, so a fault list that mentions pressure readings and a fault list that mentions speed readings are two different checks.




Q3. Does the replacement come with the cable attached?


Yes — the cable is moulded into the body, so the whole unit is replaced rather than rewired on the machine. The connector at the loom end is released and re-clipped, and the fixing screw and sealing ring are normally reused unless they are worn. Check the thread and the connector against the old unit when the parcel arrives, while the machine is still open; it takes a minute and saves a second order of crane spare parts.




Q4. Will the fault clear by itself once the new sensor is fitted?


The live reading usually returns as soon as the signal is back, but a stored code can stay in the controller until it is cleared with the machine's diagnostic tool. Run the function through one slow cycle afterwards and watch the display. If the code returns, check the connector pins and the cable run before condemning the new unit — a chafed loom produces the same symptom, and the crane electrical parts around the sensor are worth ruling out at the same time.




Q5. Is the Rexroth-branded unit the same as the XCMG-packaged one?


They are the same right-angle sensor. Some units reach the market in XCMG packaging and others carry Rexroth Bosch markings and etching, depending on which side of the supply the number was ordered from. As a crane parts supplier we check the drawing rather than the box, so either route lands on a part that matches your machine, and what arrives can be compared number for number with the old unit.




Q6. Can boom and attachment parts be supplied to suit a specific machine?


Yes. Boom sections, jib inserts and attachment parts are made to suit specific XCMG models, and discontinued or legacy references can be manufactured to order — that side of the range covers structural construction machinery spare parts rather than shelf stock. Send the machine model, the serial and either the old part number or a drawing, and the configuration is checked before the job is set up.




Review

1/3
X