Product Overview
This multi-way directional valve is the hydraulic control block for an XCMG loader crane — the component that decides which circuit receives oil when the operator moves a lever. It is a sectional valve: several control sections stacked into one body and drawn together with threaded tie rods, finished in grey paint with black caps over the spool ends.
On the machine it sits between the hydraulic pump and the working circuits. Hoist, luffing, telescoping, slewing, outriggers and steering each draw their oil through a section of this block, which makes the valve the point where a lever movement becomes pressurised oil. When one function stops responding, the valve and the crane electrical parts that command it are the first two things a technician checks.
Most of the XCMG crane parts we ship are bought for exactly that moment: the machine is down, the fault has been traced to the valve, and the repair cannot start until the right unit is on site. That is why the order is built on the number on the old valve — not on the model year, and not on a photograph alone.
As a crane parts supplier, we provide this valve as a genuine XCMG part. Each unit is matched against the number on the old block and checked against the original XCMG drawing before it leaves Shenyang, and if the reference on your machine has been superseded we tell you what replaced it.
If your technician wants a second opinion before the order is placed, a photograph of the valve, the machine plate and the surrounding pipework is usually enough for our team to confirm the reference.
How The Multi-Way Valve Works
- One section, one circuit. Each section of this sectional valve controls a single function. When its spool shifts, oil is routed to that cylinder or motor and the return oil goes back to tank, so a worn section can stop one function while the rest of the machine keeps working.
- Neutral flow. With the levers centred the spools return to the middle position and pump flow passes through the block instead of building pressure. A spool that no longer returns cleanly usually shows up first as a hot, noisy system rather than as a dead function.
- Pressure limiting. The inlet section carries the pressure-limiting function for the hydraulic control block, so a machine that has been running with a relief fault is worth checking before a replacement valve goes on.
- Holding a load. Hoist and luffing circuits depend on the valve and the holding devices around it to keep a suspended load from creeping once the lever is centred.
- The usual failure signs. A function that drifts or creeps, a lever that feels stiff or does not spring back, a circuit that is slow from cold and normal when hot, oil weeping at the joints between sections, or silt and metal in the filter — the symptoms that send most mobile crane spare parts back to the workshop.
- Why the exact reference matters. Section count, port layout and spool behaviour vary between builds. A valve that bolts up but routes oil differently will fit the machine and still not work, which is why XCMG crane parts are ordered by number rather than by appearance.
Specifications
| Part number | 804009102 |
| Brand | XCMG |
| Component type | Multi-way directional valve, sectional block |
| Machine application | XCMG loader crane |
| Circuit function | Directional control of oil flow to the working circuits |
| Position in the system | Between the hydraulic pump and the controlled cylinders and motors |
| Construction | Sectional valve with stacked control sections drawn together with threaded tie rods |
| Supply | Genuine XCMG spare parts, each matched to the number on the old unit |
| Verification | Cross-referenced against the original XCMG drawing before dispatch |
Identifying The Correct Valve
- Start with the number on the old unit. It is stamped or cast on the valve body and settles the order on its own; if it is worn, photograph it from two angles before you clean anything.
- Record the machine. Model plate, serial number and, where it is legible, the production year, so the number can be checked against the correct build.
- Note the block itself. How many sections are stacked, how many work ports leave each section, whether the spool caps sit on one side or both, and whether any crane electrical parts are mounted on the body.
- Photograph the installation. One wide shot of the valve in the frame, then close-ups of the ports, the tie rods and any markings on the body.
- Send it to us. As a crane parts supplier, we compare what you send with the original XCMG drawing and confirm whether this valve is the right one — or identify the correct reference if it is not.
- Approve before dispatch. Nothing is packed until you have confirmed the reference and the quantity, so the XCMG crane parts order is settled before the box leaves us.
Machine Coverage & Fitment
- Loader crane fitment. This hydraulic control block goes onto XCMG loader cranes and is supplied against the number on the old block. The number, not the family name or the model year, decides fitment.
- Truck and all-terrain cranes. QY25K, QY50K, QY70K, XCA100 and XCA220 sit behind most of the mobile crane spare parts enquiries we handle.
- Crawler cranes. QUY50, QUY80, XGC100, XGC150, XGC260, XGC400 and XGC650 are the crawler models we supply XCMG spare parts for most often.
- Rotary drilling rigs. XR150D, XR220D, XR280 and XR360 are covered when a rig shares a component with the crane range.
- Older and superseded references. Where XCMG has replaced a number, we trace the current reference and tell you what it corresponds to.
- If your machine is not listed. Send the model plate, the serial and a photo of the old part, and our construction machinery spare parts team will confirm the reference from the drawing.
Installation & Commissioning
- Park on level ground, lower the attachment, release the hydraulic pressure and lock out the controls before any hose is opened.
- Clean the valve area and label every hose and connector as it comes off; a phone photo of the complete installation is faster than a drawing when you refit.
- Catch the residual oil in a tray and cap the open ports and hose ends straight away — grit entering an open circuit is the most common reason a new valve fails early.
- Take out the old valve, wipe the mounting face clean, and check the fasteners and the link between the lever and the spool.
- Fit the replacement with new seals, tighten in sequence to the torque figure in the machine's workshop manual, and reconnect the hoses to your labels.
- Fill to the correct level with the oil grade specified for the machine, bleed the circuit, and work each function slowly at low engine speed before taking it to full load.
- Run the machine up to working temperature, re-check every joint for weeping, and confirm each function holds its load with the lever centred.
Related Parts For Your XCMG Machine
The valve rarely fails alone. A machine that has been losing oil, running hot or pulling contaminated oil usually needs the hydraulic side checked at the same time, so we keep the crane hydraulic parts that sit around this block — pumps, motors, cylinders, other valves, hose assemblies and seal kits — sourced to the same standard.
The command side matters just as much. Spool movement on current XCMG machines often comes from an electrical signal, so we also carry crane electrical parts — controllers, monitors, pressure and proximity sensors, relays, harnesses and cab switches — which means a fault can be traced to the valve or to the signal without waiting on a second supplier.
Beyond the hydraulic and electrical systems we supply structure and running gear as well: boom sections and jib inserts, hook blocks, sheaves and wire rope, counterweights, track shoes, rollers, sprockets and idlers, plus filters, repair kits and planetary and winch components. Buyers who handle more than one brand can draw on the same construction machinery spare parts catalogue for SANY, ZOOMLION and FUWA machines, and where a reference has been discontinued we can arrange manufacture to the original drawing — enough to put a whole repair on one order.
Ordering & Delivery
| Payment | T/T; Western Union or as agreed |
| Minimum order | 1 piece |
| Lead time | Most parts in stock. Usually need 7-20 days, according to the quantity |
| Trade terms | EXW, FOB, CFR, CIF |
| Port of loading | Shanghai, Dalian, etc. |
| Warranty | 2500 working hours or one year |
| Packing | Industrial-grade, sea-worthy wooden crates or steel frames |
| Dispatch | From our Shenyang warehouse, by air, sea, rail or express |
Valve Sections & Repair Kits
- One section can often be renewed on its own, but only once the block is identified. The sections are machined as a set, and port layout, spool travel and tie-rod length change between builds, so a section that looks identical from the outside can still route oil differently.
- Send three details before a section is quoted: the number stamped on the valve body, any marking on the faulty section itself, and a count of the sections taken from the inlet end. A photo of the tie rods and the joint faces settles most of what is left.
- Count working ports, not levers. A section may serve one function with two ports, or carry a port that feeds another circuit downstream; the port pattern on your old section is what the replacement has to match.
- The complete block is the right answer when the body is cracked, the bores are scored, more than one section is worn, or an earlier repair mixed sections from different builds. On a machine that has already been opened up twice, a fresh matched block usually costs less downtime than chasing a single section.
- Joint seals are never reused. Every time a section comes out, the O-rings and joint seals go back new, the tie rods are checked for stretch, and the nuts are drawn down in sequence so the stack stays square.
- Keep a joint seal kit for the block, the return-line filter that protects it, and a pressure gauge for re-checking the relief setting on the shelf. These are the small crane spare parts that turn a two-week wait into an afternoon's work.
- Contamination does most of the damage. Change the filter on schedule, check the oil for water and metal, and flush the circuit if the old block failed with debris in the filter — otherwise the replacement crane hydraulic parts will follow the first one out of service.
Technical Support & Model Matching
Not sure which part fits your machine? Send the part number, the machine model, and a photo of the nameplate or the worn item, and our engineers — each with more than ten years in the construction machinery business — will confirm the correct reference and quote it. We advise on installation, help trace faults, and answer technical questions before and after dispatch. Since 2017 we have built this support on a supplier network covering FUWA, SANY, XCMG and ZOOMLION, so older and hard-to-find references can usually still be sourced.
FAQ
Q1. Which XCMG machines do your parts fit?
This valve is supplied for XCMG loader crane applications, and fitment is settled by the number on the old block rather than by a model list. Across the wider range we handle XCMG truck cranes, crawler cranes, all-terrain cranes and the XR rotary drilling rigs, so if your machine is a different XCMG model, send the plate details and we will confirm the reference against the drawing.
Q2. Beyond this valve, what core parts do you supply?
Four groups: hydraulic components, electrical and safety systems, undercarriage and running gear, and boom and attachment parts — all held inside the same construction machinery spare parts catalogue. Around this valve the usual companions are seal kits, filters and the sensor or switch that commands the section; send the machine details and we will put the right group together for your repair.
Q3. Do you provide technical support for overseas customers?
Yes. Fitment and installation questions are answered before and after dispatch, around the clock, and our engineers will go through commissioning step by step with your technician — bleeding the circuit, confirming that each function holds, and reading the symptoms if something still behaves badly. As a crane parts supplier working across time zones, we keep the answers in plain English and back them with photos and extracts from the original documentation.
Q4. Do you accept customization for boom and attachment parts?
Yes. Boom and attachment parts can be built to suit different XCMG crane and rotary drilling rig models, with section, length and connection details agreed from your drawings or from the old part before work starts. The valve on this product is a different case — it is supplied as a matched XCMG spare parts reference rather than a custom item, so any customization on your order sits with the structural side.
Q5. Can a single section be replaced, or is the valve supplied as a complete block?
The valve is supplied as a complete matched block: the sections, tie rods and port layout are built as one assembly, and fitting a new section into an older block is not something we would recommend without checking the build first. Send the number and the machine details and our team will confirm whether a section is available on its own for your machine or whether the complete unit is the only correct route — that is how most mobile crane spare parts of this type are supplied.