SANY SCC1500C LINK PANEL,21004866,Q150.60.3

SANY SCC1500C LINK PANEL,21004866,Q150.60.3
Description

Product Overview

The boom link panel for the SANY SCC1500C is the heavy steel plate that ties two boom section ends together at the joint. Part 21004866 sits between the sections, carries the pin axles through its bores and holds the joint in line while the boom takes load. It is a structural part rather than a wear pin, so it comes off when the bores open up, the plate bends or the joint stops lining up — not on a fixed service interval.

We supply it new, matched to the machine by number and checked against the parts list before it is packed. Crane rental yards, fleet workshops and contractors rebuilding an SCC1500C boom order the panel together with the pins, bushings and other SANY SCC1500C parts needed for the same job, and a single panel is as welcome as a full joint set. Service items come from the same desk: the team that handles this panel also runs the wider SANY crane parts range, including SANY filters, seal kits and hydraulic components for the same machines.

Load Path & Assembly Role

  • It carries shear, not rotation. The plate is one of the crane structural parts that holds the two section ends in line and passes load between them while the pin axles and bushings take the movement. That is why a worn plate changes the feel of the joint long before anything visibly cracks.
  • Alignment is the whole job. Bores that are slightly out of position on crawler crane parts make the pins tight to fit and leave the joint working out of square, which then shows up as uneven bushing wear.
  • Wear shows at the bore. Oval holes, fretting around the pin bore, cracked paint at the hole shoulder and a plate that no longer sits flat against the section end all point to replacement.
  • Shock loads leave a trace. A dropped boom section, a transport impact or a sudden stop can bend a link plate without cracking it, so check straightness across the face before refitting.
  • Two plates can look alike. Bore spacing, plate thickness and boss height are what separate them, and the number stamped on the old plate is the only reliable way to keep the joint geometry.
  • Part of a set. In the boom assembly the panel belongs with the pin axles, bushings and section ends — the construction machinery spare parts that are inspected together whenever a boom comes down.
Red excavator bucket linkage parts with circular holes stacked in a crate.

Material & Machined Build

Panels are crane structural parts, cut from alloy steel — 35SiMn, 35SiMnMo or 28CrMnMo, depending on what the drawing calls for — then heat treated so the plate keeps its shape under repeated boom loading. The bores are machined rather than punched, which gives the pin the clearance the joint was designed around, and the boss faces are machined flat so the plate seats against the section end instead of rocking on it.

Every panel is supplied new, as heavy equipment spare parts should be. We do not pass off straightened, welded or re-bored plates as replacements, and each one is checked against its reference before packing. Paint goes on for protection in storage and transit; if your workshop needs the bores free of paint for fit-up, say so when you order and we will confirm what can be supplied.

Because these are load-bearing SANY SCC1500C parts, the drawing is what counts. If a panel is no longer listed for your build, send the original drawing — bore spacing, thickness and boss height are what we work to, and we confirm what can be made before anything is cut.

Specifications

Part number21004866
Drawing referenceQ150.60.3
ComponentBoom link panel
MachineSANY SCC1500C crawler crane
Product groupCrane boom parts
Material options35SiMn, 35SiMnMo, 28CrMnMo
Heat treatmentHardened to the OEM specification
Pin boresTwin bores, machined
Boss facesMachined flat
FinishPainted
Supplied asIndividual panel
Warranty2500 working hours or one year, whichever comes first

Fitment & Identification

  1. Start with the number on the old link plate: the part number and drawing reference stamped on the panel are what everything else is checked against.
  2. Note the machine model and serial number so the boom link panel is matched to the exact build.
  3. Photograph the joint in daylight — both faces of the plate, the pin bore and the pin itself.
  4. If the number is gone or the plate is worn, measure bore-to-bore spacing, plate thickness and boss height and send the figures with the photos.
  5. Our engineers check the reference against the SANY SCC1500C parts list and confirm what you need before an order is raised.
  6. List anything else the joint needs — pins, bushings, fasteners — so the whole set of crane spare parts ships together.
Pile of red heavy-duty chain links and link plates.

Related Boom Hardware

  • Pin axles. A new link plate on a scored or stepped pin will not stay tight; where the joint has been running loose, fit a new pin with the panel.
  • Bushings. Check the bushings in the section ends while the panel is out — a collapsed bushing puts the load straight back onto the new plate.
  • Section ends. Look for cracking or elongated holes in the boom section itself; a worn section end is the first thing to rule out on any heavy equipment spare parts joint.
  • Boom head. A boom that comes down for a panel change is the moment to inspect sheaves, wire rope and head fittings, and we quote those crawler crane parts from the same stock.
  • Service items. Workshops rebuilding a machine often add crane spare parts such as SANY filters, seal kits and hoses to the same shipment so the crane goes back to work on one delivery.
  • Mixed lists. As one of the construction machinery spare parts suppliers covering SANY, ZOOMLION, XCMG and FUWA, we price a joint set and the parts around it on a single inquiry.

Replacement Procedure

  1. Lower the boom section onto stands and work to the SANY service manual for the machine before any pin is released.
  2. Drive out the pin axles and keep shims, spacers and fasteners in order — they go back exactly as they came out.
  3. Clean the section ends, dress any burrs and check the bushings before the new panel goes in.
  4. Trial-fit the panel dry: the bores should line up with the section holes without forcing, and the plate should sit flat.
  5. Fit the pins and fasteners and tighten to the torque figures in the manual, not to feel.
  6. Log the date, machine hours and the reference fitted against the crane's maintenance record.
  7. Re-check pin retention and joint alignment after the first shifts of work, and again at the next service.

Ordering & Delivery

Payment termsT/T; Western Union or as agreed
Minimum order1 piece
Lead timeMost parts in stock; usually 7-20 days, according to the quantity
Trade termsEXW, FOB, CFR, CIF
Loading portsShanghai, Dalian, etc.
Warranty2500 working hours or one year
PackingPlywood box
Urgent ordersPriority air freight on request
Multi-piece ordersVolume pricing on request
Red leaf springs with black bushings and yellow center wrap in packaging.

Technical Support & Model Matching

Not sure which part fits your machine? Send the part number, the machine model, and a photo of the nameplate or the worn item, and our engineers — each with more than ten years in the construction machinery business — will confirm the correct reference and quote it. We advise on installation, help trace faults, and answer technical questions before and after dispatch. Since 2017 we have built this support on a supplier network covering FUWA, SANY, XCMG and ZOOMLION, so older and hard-to-find references can usually still be sourced.

FAQ

Can you still supply this link panel for older SCC1500C builds?

Yes. We still supply crawler crane parts for older SCC1500C builds and earlier SANY models: send the machine model plus the number on the old plate, or a drawing if the number has gone. Where a reference has dropped off the list, we match it through our supplier network or have it made to drawing — which is what buyers need from crane parts suppliers when the machine is ten or fifteen years old. The same desk covers crane boom parts for the rest of the assembly.

How do I verify that a link panel matches my crane?

Work from the plate itself rather than from the model alone. The number and drawing reference on the old panel, plus the machine serial number, let our engineers confirm the fit, and photos of the joint settle the rest. If the stamping has worn away, bore-to-bore spacing, plate thickness and boss height measured off the old plate identify it even when the part is worn — the same check we run on any construction machinery spare parts line before it ships.

Is the panel supplied with pins and bushings?

The panel is supplied on its own. Pins, bushings and service items such as SANY filters are separate crane spare parts, and they are listed with the panel when you send your joint list so everything arrives together.

Can the panel be made to a drawing, or supplied in a different finish?

Yes. Where a reference is no longer available, or where your build differs from the standard, send the drawing and our engineers review bore spacing, thickness and boss height for these crane structural parts before anything is cut. Finish is worth agreeing up front: panels are painted for protection, and if your workshop prefers to paint after fitting, tell us and we will confirm what can be supplied.

Should both plates at a joint be replaced at the same time?

Inspect both before deciding. If one bore has opened up, the opposite plate and the pin usually show related wear, and leaving one worn plate in place puts the load back onto the new part. Check the section ends and bushings in the same pass — the rule that applies to any heavy equipment spare parts joint that has been running loose.

Review

1/3
X