Spare Parts GFT60 Series Brake Disc For Gearbox

Spare Parts GFT60 Series Brake Disc For Gearbox
Description

Product Overview

This brake friction disc is made for the GFT60 series planetary gearbox as a direct replacement for the pack inside the brake housing on a hoist or travel drive. The body is cast steel with a friction lining bonded to the face, so the disc takes the same clamping pressure and heat cycling as the part it replaces. When an old pack starts to slip, glaze or drag, this is the piece that brings the holding power back without disturbing the gear set or the housing.

Most orders for this disc come through our crane spare parts range, and it is one of the mobile crane parts we stock, because that gearbox is fitted to machines of several ages and in several markets. SANY, FUWA, ZOOMLION and XCMG cranes built years apart can carry the same brake pack, so one reference often covers more than one unit in a fleet.

We supply fleet workshops, repair shops and other crane parts suppliers who need a single set to finish a repair rather than a complete reducer. In most cases the rest of the drive goes back into service untouched.

Construction & Friction Stack

  • Cast steel body. Instead of being pressed from sheet, this cast steel brake disc holds its shape under repeated clamping and does not dish when the brake runs hot.
  • Bonded friction lining. The tan lining bonded to the face is the surface that actually stops the load. Bond integrity and lining thickness on each brake friction disc are what a replacement pack is really paying for.
  • Steel separator plates. The pack alternates lined friction discs with plain steel plates, and the steel plate is the reaction face the lining clamps against. It has to be flat and unscored to be reused.
  • Toothed outer rim. The outer teeth locate the disc on its carrier and carry torque out of the pack. Check the tooth flanks on the old GFT60 brake disc, because a chewed rim means the carrier needs attention too.
  • Splined inner bore. The internal spline drives the disc on the hub. Burrs or slack here will make a new hoist brake disc sit off-centre, so clean the spline before assembly.
  • Stacked construction. The brake works as a stack of alternating plates, not as one thick disc. That is why the pack is normally renewed as a set matched to the gearbox build.
  • Position in the drive. The pack sits between the drive motor and the planetary stage, so braking force is taken inside the gearbox housing rather than by a separate external brake.

Specifications

Product typeGearbox brake disc (friction disc and steel plate pack)
SeriesGFT60
FitsGFT60 series planetary gearbox, in the brake housing
Machine brandsSANY, FUWA, ZOOMLION, XCMG
Disc bodyCast steel
Friction facingBonded tan friction lining
Outer edgeToothed rim
BoreSplined inner bore
Stack layoutAlternating friction discs and steel separator plates
Typical useHoist and travel drives on crawler and mobile cranes
Condition100% new; no refurbished or used parts
CategoryConstruction machinery spare parts, crane transmission and brake components
Metal clutch plates, friction discs, and circular seals.

Fit & Compatibility Confirmation

  1. Start at the gearbox plate. Note the full code stamped on the reducer housing, because the gearbox brake disc is matched to that build code and not to the crane model alone.
  2. Record the machine brand, model and serial number as well. The same crane can leave the factory with more than one hoist drive specification, and the serial number settles which one you have — crawler crane parts lists and truck-mounted lists overlap more often than most workshops expect.
  3. Send the number stamped on the old brake friction disc, or the reference from the gearbox parts book if the plate is worn past reading.
  4. Measure the parts that came out: outside diameter, bore and spline, disc thickness, and how many lined discs and steel plates were in the stack. Include these figures with your enquiry.
  5. Lay the old pack out in order and photograph it, then photograph the gearbox plate. A picture of the worn stack answers most fitment questions in one message.
  6. Tell us if the repair also covers hydraulic crane part items such as the drive motor or valve block, and we will check those references at the same time.
  7. We confirm the GFT60 brake disc reference against your gearbox build before dispatch and tell you if a different disc is the correct one for your unit.

Wear Signs & Replacement Timing

How a worn pack behaves. A brake near the end of its life rarely fails without warning. The load creeps down after the control is released, the brake drags or runs hot, engagement brings a chatter or grinding noise, and the control needs more travel than it used to. Operators usually sense the creep before the crane load indicator shows anything unusual, and a hoist that will not hold is the most common reason these packs come out.

What to look for on the bench. Glazed, cracked or lifting lining, blue heat marks on the steel, scored faces, worn or burred teeth on the outer rim and a slack spline in the bore all point to replacement of the cast steel brake disc rather than reuse.

Oil contamination. A leaking hydraulic crane part, usually the brake piston or a shaft seal, softens the friction lining, and the pack loses grip even though the plates still look thick. On an oil-immersed drive this is the failure that catches workshops out, because nothing looks worn.

No fixed interval. Hoist duty, load and oil condition vary too much between machines for a single replacement hour figure to mean much. Judge the pack at every service, and repair the leak or the adjustment fault before fitting a new disc, otherwise the same construction machinery spare parts bill comes round twice.

Installation Notes

  1. Lock out the machine and land the load. The hoist brake disc is holding the hoist, so release the tension and support the drum before you open anything.
  2. Drain the oil and open the brake housing in a clean area. Grit or swarf inside a new GFT60 brake disc pack is the quickest way to lose the repair.
  3. Lay the old stack out in the exact order it came apart and note which plates are lined discs and which are plain steel.
  4. Clean and inspect the carrier teeth and the hub spline. Remove burrs with a fine file, and set aside any steel plate that is scored, warped or heat-blued.
  5. Fit the new cast steel brake discs in the same order, lining facing its steel plate. Keep the friction faces free of grease, and follow the gearbox manual on pre-lubrication.
  6. Check the brake piston, seals and reaction plate before closing the housing. A leaking piston is the hydraulic crane part that will contaminate the new pack within hours.
  7. Refill with the specified oil, set the brake to the manual, and test holding capacity on a light load with the crane load indicator in view before the machine goes back to work.

Model Reference & Replacement Scope

  • One part of a bigger drive. This listing covers the brake disc pack, not the complete reducer. If the gear set, bearings or housing are damaged, the whole unit is a separate repair and should be quoted on its own.
  • Identified by the gearbox code. The plate on the housing carries the frame size, build number, ratio and brake arrangement. Quote the full code when you ask for a price so the disc is matched to your build.
  • Older machines. Cranes that are out of production or no longer backed by the original dealer are routine work for us. Send the model, a drawing or a photo of the old part and we will trace the reference.
  • Crawler crane parts. The same drive is used on crawler crane hoists as well as on foundation rigs, so one pack can cover several machines in a crawler fleet.
  • Mobile crane parts. Truck-mounted and rough-terrain cranes built around the same gearbox take the same disc, which lets a workshop keep a single reference on the shelf.
  • Electrical and monitoring items. Cables, monitors, controllers and other crane electrical components are handled separately, so tell us if the repair needs them.
  • Drawings and modified drives. If the unit has been modified or the plate is missing, send a sketch with diameters, tooth count and stack height, and our engineers will review it against the original.
Brake disc friction plates, steel separator plate, and packaging label.

Ordering & Delivery

PaymentT/T; Western Union or as agreed
Minimum order1 piece
Lead timeMost parts in stock. Usually 7-20 days, according to the quantity
Trade termsEXW, FOB, CFR, CIF
Port of loadingShanghai, Dalian, etc.
Warranty2500 working hours or one year
Multiple setsVolume pricing quoted on request
Critical repairsAir freight can be arranged when the machine is down

Technical Support & Model Matching

Not sure which part fits your machine? Send the part number, the machine model, and a photo of the nameplate or the worn item, and our engineers — each with more than ten years in the construction machinery business — will confirm the correct reference and quote it. We advise on installation, help trace faults, and answer technical questions before and after dispatch. Since 2017 we have built this support on a supplier network covering FUWA, SANY, XCMG and ZOOMLION, so older and hard-to-find references can usually still be sourced.

FAQ

Can I replace just the friction discs and keep the steel plates?

Yes, if the plates come out flat, unscored and free of blue heat marks, they can go back in with new lined discs. Anything warped, discoloured or scored should be renewed with the pack, because a rough plate will grind a new lining down within a few shifts. Send a photo of the plates laid out and we will tell you which ones are worth keeping.

Do you supply brake packs for other GFT gearbox sizes?

Yes. The GFT family covers several frame sizes and we handle reducer and gearbox parts across the range, not only this one. Send the code from your gearbox plate, frame size plus build number, and we will confirm what is available for that unit.

Is the brake disc supplied with the seals and bearings for the same repair?

The listing covers the brake disc pack itself. If the same repair also needs seals, bearings or other crane spare parts, say so when you send the gearbox code and we will quote them on the same order so everything arrives together.

Does the brake pack work with the crane load indicator?

The pack is a mechanical brake component with no electronics inside it. Load and moment monitoring runs through the crane load indicator and limiter system, which is a separate part of the machine. If the warning you are chasing comes from the monitoring side rather than the brake, tell us and we will point you to the right item.

Can the pack be changed with the gearbox still in the machine?

On most hoist drives the brake housing can be opened in place, provided there is access from the deck or engine side and the area can be kept clean. If the gearbox is coming out anyway for bearing or gear damage, fit the pack on the bench, where the carrier teeth and spline can be checked properly.

Review

1/3
X
Subscribe To Get The Latest Quotation
Please leave your email address. We will regularly send the latest catalog to your email.