XCMG QUY80,QUY150,QUY650,pressure sensor,803602252.

XCMG QUY80,QUY150,QUY650,pressure sensor,803602252
Description

Product Overview

Cylindrical threaded connectors sealed in clear plastic bagsHirschmann threaded cylindrical components in clear plastic bags

A crane that has stopped trusting its pressure reading is out of service until that reading can be trusted again. This sensor screws into a pressure port on the QUY crawler crane range and sends the reading back to the cab, so the operator and the machine's monitoring system can see what the circuit is doing. It is a small item with a large effect on uptime, and it sits firmly on the everyday crane spare parts list for anyone maintaining these machines.

Most orders start in one of two places. A machine has thrown a fault, a reading has flat-lined or a function has gone rough, and the technician needs the right unit before the next shift. Or a service interval has come round and a drifting sensor is being changed before it causes a stoppage. Either way the job needs a unit that matches the original thread, plug and signal output — the sort of construction machinery spare parts order where the number on the old unit matters far more than any description.

A good share of the cranes we supply are well past their first decade. Bringing a used crawler crane back into service usually turns up a handful of small electrical faults, and a pressure sensor that no longer tells the truth is one of the most common: the machine still runs and lifts, but the display is guessing.

Sensor Function and Signals

  • Threaded body, sealed port: the sensor screws straight into a pressure port, and the hexagonal collar gives a spanner a proper grip so the body turns without being twisted off the fitting.
  • Signal, not guesswork: pressure at the port is converted into an electrical signal that the crane's monitoring system reads, displays and acts on.
  • Where the reading goes: it feeds whichever function that port serves, typically a hoist, luffing or travel circuit depending on how the machine is laid out.
  • Why accuracy matters: the limiter and the operator's display work from the same number, and the load charts and safety logic assume that number is honest.
  • Part of a wider circuit: it works alongside the other hydraulic crane parts on the machine — pumps, valves, cylinders and hose assemblies — and a fault in any of them can imitate a sensor failure.
  • Checked with the boom: boom-hoist and luffing pressures pass through these ports, so the sensor is normally inspected in the same window as crane boom parts, sheaves and wire ropes.
  • Simple connection: the plug is threaded and seats by hand, so a careful technician can change the unit on site with ordinary tools.

Model and Part Number Matching

Order against part number 803602252. It is the reference printed on the sensor body and the one used on the XCMG parts drawing, so it is also the first thing our engineers check before a unit is packed.

The number is listed for the QUY crawler crane range. If your machine is a different model in the family, do not assume — send the number from the old sensor and we will read it against the drawing. Fitment on crawler crane parts is settled by the number and the port, not by the badge on the cab.

This is where most wrong-part orders begin. Listing a sensor as fitting an entire model range is easy; the useful work happens before dispatch. We keep the original drawings to hand and read them against your serial number and the number on the old unit, which is the part of the job many crane parts suppliers leave to the buyer.

A photo of the old sensor, its label and the machine serial number are usually enough for us to confirm the match.

Specifications

Component type Hydraulic pressure sensor
Brand XCMG
Part number 803602252
Machine family QUY crawler crane
Listed models QUY80, QUY150, QUY650
Condition New, not refurbished
Housing Cylindrical metal body
Port end Threaded, with hexagonal collar
Electrical end Threaded plug connector
Marking Wraparound label carrying the part number
Working role Converts pressure at the port into an electrical signal for the cab display
Typical mounting Pressure port on a hoist, luffing or travel circuit
Fitment check Thread, plug and signal output matched against the old unit before dispatch
Packing Export packing suited to sea, air or rail freight

Fault Symptoms and Diagnosis

  • A reading that will not move: the display holds a fixed value whatever the machine is doing.
  • A reading that wanders: the number drifts as the oil warms up, or jumps between values without a change in load.
  • Intermittent faults after rain or a wash-down: water in the plug is more often the cause than the sensor itself, and the connector is the first thing to open.
  • A function that feels wrong: luffing, hoisting or travel that is jerky or slow to respond with no obvious mechanical cause.
  • Warning or limiter behaviour: the safety system derates or blocks a function because the pressure signal it is being fed does not add up.
  • Chasing the fault on an older machine: on a used crawler crane the loom and plug have usually had a harder life than the sensor, so check continuity before condemning the part.
  • Before you order: confirm the port is clean, the plug is dry and the earth is sound. It is easy to spend a crane spare parts budget twice by swapping a healthy sensor for another healthy sensor — the kind of repeat order crane parts suppliers would rather talk you out of.

Replacement Procedure

  1. Park the machine on firm, level ground, lower the boom to its rest position and shut down following the crane's own procedure.
  2. Release hydraulic pressure from the circuit before opening anything — the same discipline you would apply to any hydraulic crane parts job.
  3. Photograph the connector and the hose routing before you touch them, and note the number on the old sensor's label.
  4. Clean the area around the port so nothing drops into the circuit when the sensor comes out.
  5. Unplug the connector, then unscrew the sensor using the hex collar. Hold the body, never the cable.
  6. Inspect the port thread and the sealing face. If either is damaged, deal with the port before fitting a new unit.
  7. Fit the replacement, tighten it to the torque given in the machine's service manual and push the plug on until it seats.
  8. Start up, run the function that the sensor serves through a full cycle and watch the display. Check the port for weeping before the machine goes back to work.
  9. If the reading is still wrong with a known-good sensor fitted, move to the wiring and the control side rather than ordering another part.

Related Parts and Combined Sourcing

  • Electrical and control: sensors, limiters, controllers, monitors, cables and switches for the same machines.
  • Boom and structure: crane boom parts including boom sections, jib inserts, boom foot assemblies and hook blocks.
  • Undercarriage: crawler crane parts that take the ground pressure — track shoes, track rollers, idlers, drive sprockets and tension devices.
  • Hydraulic: pumps, motors, valves, cylinders and seal kits.
  • Workshop consumables: filters, repair kits and seal kits — the heavy equipment spare parts that get used up between major repairs.
  • XCMG machine coverage: from the QUY crawler range through the XGC, QY and XCA cranes to the XR rotary drilling rigs.
  • Mixed fleets: alongside XCMG we handle SANY, ZOOMLION and FUWA, so construction machinery spare parts for a whole yard can be quoted together instead of one brand at a time.
  • Older units: discontinued and legacy references are traced rather than refused, which is often the difference between repairing a machine and parking it.

Ordering and Delivery

  • Minimum order: 1 Piece
  • Payment: T/T; Western Union or as agreed
  • Lead time: Most parts in stock. Usually need 7-20 days, according to the quantity.
  • Shipping: Port of Loading: Shanghai, Dalian, etc. Trade Terms: EXW, FOB, CFR, CIF
  • Warranty: 2500 Working Hours or One Year
  • Packing: electrical items are boxed and cushioned for export, while larger structural parts travel in sea-worthy wooden cases or steel frames.
  • Consolidation: if the same job also needs heavy equipment spare parts for other machines or other brands, they can be combined into one shipment.
  • Availability moves quickly on electrical items, so confirm the current position with your sales contact before you book the repair window.

Technical Support & Model Matching

Not sure which part matches your machine? Send us the model, serial number and the original part number — or a photo and key dimensions — and our engineers will confirm the correct item and check availability before you commit. They have spent more than ten years in construction machinery and can talk you through fault-finding, installation and commissioning by phone, email or video. We also trace parts for discontinued and legacy models. Support runs 24/7 from Shenyang, China, where we have been supplying buyers since 2017.

FAQ

Which XCMG models does this pressure sensor fit?

It is supplied for the QUY80, QUY150 and QUY650 crawler cranes. Crawler crane parts change between builds, so the number on the old sensor is what we check before quoting rather than the model name alone. If your crane is another QUY model, send the number and the serial number and we will read them against the drawing.

How do I confirm the part number before ordering?

Read it off the old unit. Most crane spare parts carry the number on the body or on a wraparound label, and a clear photo of that label together with the machine serial number is usually enough for us to confirm the match. If the label has worn away or been painted over, send a photo of the port and plug instead.

Can this sensor be fitted to a used crawler crane?

Yes, provided the number on the old unit matches. Older machines deserve a closer look at the plug and the port thread first: corrosion in the connector and a damaged sealing face will make even a new sensor read badly, and both are cheaper to sort out before the unit goes in.

What other XCMG parts can you supply with the sensor?

Hydraulic, undercarriage, structural, electrical and maintenance items — pumps, valves, cylinders, track shoes and rollers, boom sections, controllers, monitors, filters and seal kits. Ordering construction machinery spare parts as one list means one quotation to review instead of five.

Do you provide technical support for overseas customers?

Yes. Our engineers handle fault-finding by phone, email and video: connector checks, the readings you should expect, and what to look at after fitting. Good crane parts suppliers are judged on what happens after dispatch, so if the sensor still reads wrong on a known-good circuit we will help trace it to the wiring or the control side before you buy another unit.

Do you accept customization for boom and attachment parts?

Yes. Structural items are made to drawing — crane boom parts such as boom sections, jib inserts and boom foot assemblies, plus attachment parts for XCMG cranes, including discontinued and legacy models. Send the drawing or the key dimensions and we will quote against them. This sensor itself is a standard electrical part, so it is ordered by number rather than by drawing.

What does the sensor control on the crane?

It does not control anything; it reports. Pressure at its port becomes an electrical signal that the monitoring system and the operator's display use, and the machine's own logic decides what to do with that number. That is why a drifting unit can feel like a control fault even when the other hydraulic crane parts on the machine are working normally.

Review

1/3
X